1. Current Location: Home >  Router settings >  The router has clearly set a speed limit, so why is that machine still running at full speed?

The router has clearly set a speed limit, so why is that machine still running at full speed?

Three major causes of router speed limiting not taking effect: The unit is entered incorrectly, the terminal’s built-in speed limit is not turned off, and IPv6 traffic bypasses the speed limit.

The broadband at home is 300M, and the router backend limits it to 50M for my brother's desktop computer that is connected to downloads. After filling in the form and clicking Save, the network was still stuck in PPT that night. I went into the background to take a look, and found that the speed limit rules were in place and the machine name was correct, but his download speed was actually 278. So lonely. It took me until one o'clock in the middle of the night to find out all three root causes. The most sinister one is related to IPv6. I wrote it down to save a night for people who also "limited it and it didn't work."

first place: The unit misunderstood, it means there is no limit

The first mistake I made was the most basic, but also the most common. The speed limit page of the Mercury machine said "KB/s". I was thinking of 50 megabits, so I filled in 50 on my hand. Looks like there's nothing wrong with it, right? 50KB/s, four hundred kilobits per second, not much faster than the dial-up era. And the same machine changes the entrance, Tenda AC10 adopts IP segment speed limit page, the unit is Kbps. Two sets of pages and two sets of units from the same company, the difference is eight times: 8 Kbit is 1 KByte.

So do one thing first after the deadline: Don't believe the page that says "Setup successful", go directly to that machine to run a speed test or look at the speed bar of the downloaded software. The second time I filled in the unit correctly, 50MB was filled in as "6400KB/s" or "51200Kbps" (the two writings mean the same thing), and his download was immediately listed at around 46MB. The symptoms of filling in the wrong unit are very identifiable: Either the limit is extremely harsh (my limit was 50KB/s that night, he couldn't even open the web page, and he thought he was blocked), or there is no change at all. If you touch both ends, you can basically lock in the unit problem. The article about dismantling broadband in a shared house I divided the accounts among three lines, and I was deceived by these two units twice before I remembered it.

second place: The device recognized by the speed limit rule may no longer be that device.

Even if the unit is correct and it still doesn't work, the second thing to check is the anchor point where the speed limit rule is hung. The function that the router takes effect according to the device does not recognize the machine name, but the MAC address. The random MAC article I’ve talked about this underlying logic. Today's mobile phones and many computers have "random MAC/private address" turned on by default, changing the virtual address every time they connect or every few days. The rules are hung on the old MAC, and the device enters the site with a new MAC. The router treats it as a brand new device - no speed limit, green light to let it go.

My brother's desktop computer is not a random MAC problem (desktop network cards generally do not have this set of network cards), but when I was troubleshooting, I saw a familiar scene in the device list.: The "Brother's Desktop" that was named "Brother's Desktop" appeared next to it three days ago, and an Unknown appeared next to it. The first six digits of the MAC were exactly the same. The rules are posted on the famous channel, but the actual traffic goes through the unknown channel. Two treatments: Either go into the WiFi details page of that device, turn off the random MAC, and use "device MAC" instead, once and for all. ; Or change the speed limit on the router side from "by device" to "by IP segment", for example 192.168.1.100 Enter all the numbers to 110. If you have renamed or sorted the equipment at home, take a look. Unknown device recognition article , understand the list clearly and then set the rules, otherwise the wrong person will not know the speed limit.

The third place: IPv6 bypasses speed limits, old routers are hardest hit

This was my real culprit that night, and the one that no one talks about the most. Now operators issue IPv6 by default, and mobile phones, computers, and downloaded software all use v6 first. Here comes the problem: The speed limiting function of many routers (especially old firmware and hundreds of yuan machines) was implemented early. At that time, home broadband was still purely IPv4, and the rule engine was only hung on IPv4 traffic. The device gets the v6 address and goes out through the v6 channel without even looking at the speed limit rules. I fiddled with the background speed limit page for two hours, and finally disabled v4, leaving only v6 for testing - the download speed was running at 278, and it was only at that moment that I realized that the traffic was not going through the door I was configuring.

The verification method is very simple and only takes one minute: Open the command line on the restricted machine, use Windows ping -6 www.shunot.com , if it can pass, it means it is running v6. Then check the instructions on the router's speed limit page (or directly ask customer service if the firmware supports v6 speed limit). Three processing levels: The firmware is new and will most likely be supported after upgrading. First update the router firmware to the latest and try again. ; The firmware is old but the machine itself is fine. Simply turn off IPv6 in the router LAN settings or limit it to "link local only". FamilyMart returns v4 and the speed limit takes effect immediately - the cost is that the benefits of v6 are gone and the home use case is basically useless. ; If the machine is too old and cannot be modified, use the software side speed limiter to avoid the problem. The downloaded software comes with a full speed limiter, which is more accurate than a router. You can watch it if you want to turn off v6 The article about opening IPv6 Deciding again, my family finally solved the problem by upgrading the firmware. I turned off the v6 path for my mother-in-law's old machine.

There is also a parallel pit: The fight between speed limit and software speed limit

By the way, the symptoms are similar but the origin is different. Download the software and turn on "Smart Speed ​​Limit" or "Full Speed ​​in Idle Time". You have a maximum limit of 50 MB on the router. When the software sees that the bandwidth is sufficient, it will increase the speed to the maximum limit. Both sides have their own say. My brother's machine was installed with a download tool last quarter, and "Night Full Speed" was checked by default. Although the router's speed limit took effect after 9 p.m., the software detected that no one was using it at night and filled up the thread. I saw from the router's traffic monitoring that it still ran 180G overnight. The solution is to turn off "full speed period" and "intelligent scheduling" in the software settings, and let the router be the only speed limit referee. Don’t blame the router for tool problems. If the traffic account doesn’t match up, you can still check it. Go backstage and find out the root cause of the speed limit in five minutes Go through the troubleshooting path in that article again.

As a reminder, just because the speed limit rules are in effect does not mean everything will be fine. After some machines are speed-limited, the router CPU cannot handle it (QoS is soft processing, which consumes computing power), the network speed of all employees drops, and the game ping value goes up to 200 - this is QoS switch article As mentioned above, if the hardware is too weak, do not forcefully enable QoS for the whole family. Just set a single speed limit for individual devices.

Follow the order of verification one by one.

At the end of that night, I summarized a shortest path. When I was frustrated by the speed limit not taking effect, I checked it in this order. Each step took less than one minute.:

order What to check Characteristics of a hit action
1 Is the unit correct? After the limit is over, the speed will either stay close to the ground or remain unchanged. Confirm KB/s and Kbps, 8x relationship conversion and refill
2 Is the device linked to the rule still there? A new Unknown with the same prefix MAC appears in the device list Turn off random MAC or change speed limit by IP segment
3 Is the traffic going through v6? Ping -6 on the machine works, but v4 is turned off and the speed remains unchanged. Upgrade firmware/turn off IPv6/software speed limit
4 Is there a second set of speed limits on the software side? Router monitoring shows traffic surges at night Turn off full-speed scheduling of download tools

My order is first 1, then 2, then 3. The first two are low-cost to start with. The IPv6 one involves the choice of whether to turn off v6, so I will make the final decision. The three root causes of the disease were all cleared up, my brother's computer ran steadily at 46MB, and the TV in the living room finally stopped spinning that night. The speed limit at home is always the same as if it is set, and it will probably fall into one of these three places. Don’t rush to change the router, go through these three places first.

Read More


Copyright Notice Scan to read on mobile
All Rights Reserved: 《SHUNOT》 => 《The router has clearly set a speed limit, so why is that machine still running at full speed?》
Article URL: https://www.shunot.com/en/luyou/1581.html
Unless otherwise stated, all articles are original by 《SHUNOT》. Reposting is welcome! Please indicate the original URL when reposting, thank you.

Contact Us

Online Consultation: Click here to send me a message

WeChat ID: master_135

Scan to follow