The panel AP was changed from WiFi5 to WiFi6. I changed the four panels in three nights.
The AC+AP in the new house was renovated in 2023. The four WiFi5 panel APs have been in service on the wall for three years, and I don’t usually feel anything wrong. This year's Double 11, my family changed to two mobile phones that support WiFi6, and the TV in the living room was also changed from 55 inches to 75 inches. The problem arose.: The speed of the mobile phone measured in the study room was only over 200 Mbit/s, and the TV occasionally had to buffer when watching 4K. At first I suspected that it was a matter of broadband. I connected the network cable directly to the optical modem and measured the full speed. Then I measured the WiFi again. The difference was there - it was not that the broadband was slow, but that the four old panels on the wall could no longer feed new equipment.
Change it. But before I changed it, I thought for a long time about how to change it without paralyzing FamilyMart.: There are about 40 smart devices at home, including sweeping robots, cameras, and door locks, all pointing to WiFi. They are all dismantled and replaced with new ones. During those few hours when the whole family is disconnected from the Internet, Mijia devices can perform a collective offline for me. This article will record the complete process of my replacement, including several pitfalls that I didn’t expect to encounter before the replacement.
Calculate three accounts before switching, don’t place an order directly
I first settled the calculation of "is it worth changing?" The broadband at home is Gigabit, and the theoretical speed of the WiFi5 panel is 433 Mbit/s (5G band single stream). The actual speed of more than 200 Mbit/s is normal. ; The single stream of the WiFi6 panel can reach 1200 Mbit/s, and the actual rate is 400 Mbit/s or 500 Mbit/s. The two new mobile phones support WiFi6 and the TV supports WiFi6. This is the profit side of the exchange. ; However, devices such as sweeping robots and door locks that only recognize 2.4G will remain at the same speed whether or not the panels are changed, so there is no advantage at all. Therefore, what is being replaced is the "fast lane of mobile phones and computers." Not all devices will be accelerated. This expectation must be corrected first.
The second account is money. Four WiFi6 panels, TP’s AX1900 costs just over 200 yuan for one, and more than 800 yuan for four. Old panels could be sold for thirty or forty yuan a piece second-hand, but the four pieces I had used for three years were in average condition, so I finally packed them up and sold them for eighty yuan, which was better than nothing. This price is not expensive compared to replacing the whole machine with Mesh, but if your broadband is only 300 Mbit/s, or the main equipment in your home are all three-to-five-year-old mobile phones, this money can be saved - if the WiFi5 panel is not broken, you don’t need to move it. This is not a consumable, and there is no need to replace it at the end of the year.
The third account is a compatible account, and it is also the one I am most worried about.: The all-in-one AC machine at home is TP-LINK’s TL-R47X series. I bought it three years ago. Does it recognize the new WiFi6 panel? You need to confirm this before placing an order, not discover it after dismantling it. I checked the firmware version of the AC and looked through the support list on the AP management page. WiFi6 panels of the same brand were listed. If your AC is too old and the WiFi6 panel model does not even appear on the management page, then you must either upgrade the AC firmware first or replace the AC together - then it is not called an upgrade, it is called a reinstallation. I advise against cross-brand mixing. The management protocols of panel APs of different ACs are not interoperable. Brand A ACs are linked to brand B panels. At best, they cannot be seen in the management page, and at worst, the POE power supply negotiation cannot be matched.
Bottom box depth: An old problem that was only exposed after replacing the panel
The first pitfall was discovered only two days before placing the order. The WiFi6 panel is thicker than the WiFi5 panel. The one I'm interested in is marked "Adapted to 45mm deep bottom box." However, during my renovation, the electrician used a standard 40mm bottom box for the network port position. The WiFi5 panel that was installed back then fit right in, but this time I replaced it with a new one, and the one in the study room almost couldn't fit in - when the panel was pressed into the box, the network port connector hit the bottom of the box, and the panel floated outside, like a tile that was not firmly attached.
By the way, the network cable from the AC to the panel in the weak current box does not need to be touched. The WiFi6 panel still uses the same cable and is powered by POE, but after changing to a new panel, I specifically took a look at the POE standard.: The old panel is 802.3af, and the new panel is also nominally AF, which is exactly the same. If the new panel you buy is 802.3at (high power), and the POE port of the AC all-in-one only outputs AF, and the panel lights up but does not work properly or even restarts repeatedly, it only takes a minute to check these parameters on the AC specification page before placing an order. How to choose an AC all-in-one machine? I have written about the total POE power here. When replacing the panel, the power consumption of each panel must be added again. Don't let the new panel blow up the AC's POE budget.
Change order: Why are we moving room by room?
The day it arrived was Thursday night, I only dismantled the master bedroom. It's not procrastination, it's intentional: Change one piece first to see if the AC recognizes it, whether the old equipment can be connected, and confirm that the entire process is OK before moving on to the remaining three pieces. This step really saved me - after replacing the one in the master bedroom, the AC management page showed that it was online but the model column was empty. I stared at the empty column for ten minutes and found out that the firmware of the new panel was newer than the AC management firmware. The AP list had to be refreshed manually before the model number could be read out. It would be unimaginable to imagine that all four rooms were demolished in one go, and something like this was discovered in the middle, and the whole family was disconnected from the Internet and waited.
In order, I sorted by "replace the one farthest from the weak current box first": The master bedroom is at the farthest end. Changing it first is equivalent to testing the one with the longest link first. ; The second night in the study room, the third night in the children's room and restaurant. Every time a piece is changed, the process is a fixed four-step process.: Remove the old panel (tighten two screws and pull out the crystal head of the network cable), wire the new panel (insert the crystal head all the way and listen for a click), wait two minutes for power on (AC needs to identify the device), take your mobile phone into the room and connect to the WiFi to test the speed. Don't waste two minutes waiting. When the panel is first powered on, the AC is still shaking hands. If you go to the management page immediately and see it, what you see is probably "offline". Wait and see again to see the real status.
There is another detail that only panel AP users understand.: When replacing the panel, WiFi is disconnected in that room, but other rooms are not affected - this is the benefit of the AC+AP architecture. One panel only affects one room. When I changed the master bedroom on the first night, I had to watch the TV and sweep the floor in the living room. Only the master bedroom had no internet for ten minutes. If the entire Mesh or router needs to be replaced, this kind of "local surgery" cannot be done, and the entire house must be cut off at the same time. This point is Comparison of networking solutions I have done the calculations here, and I will have a deeper experience when changing generations.
Same name and password: Key operations that make the device “senseless”
The biggest fear when replacing the panel is not that it won't fit into the bottom box, but that the network of forty devices will be reconfigured one by one. What I did was to copy down the SSID and password of the old panel before replacing them.: The WiFi name of the old panel is named according to the room, such as "home-master", and the password is sixteen digits. After the new panel is powered on, go to the AC management page and change the SSID of the new panel to be exactly the same as the old one, and the password is also exactly the same. In this way, the device doesn't even know that the panel has been changed, and it will automatically connect to the new panel when you walk near the room - they recognize the name and password, not the panel itself.
But there is one difference that you need to think about in advance: The old WiFi5 panel is dual-band in one, with 2.4G and 5G mixed in one SSID. ; The new panel also has dual-band integration by default, but the default "band selection" logic is different from the old panel. The result is that some devices hold on to 2.4G after connecting to the new panel first - even though the phone supports 5G, the speed immediately drops. I am experiencing this phenomenon The article about dual frequency in one I specifically wrote about how to adjust it: Either widen the gap between the transmit power of the two frequency bands, or simply turn off the dual frequency bands and separate them into two names: "home-master" and "home-master-5G". I directly chose the latter this time, and it was done in one step. After that, which device should be in which frequency band? My own mobile phone and computer were connected to the 5G name, and the sweeper door lock was connected to the original name. Each one has its own place.
There is a time window to pay attention to when changing the name.: In the few dozen seconds after the SSID of the new panel is changed, the old devices will reconnect collectively, and the device list of the Mijia App will flash "offline and online again." The first time I saw it, I was a little panicked, but after seeing it more, I realized that it was a normal phenomenon. Wait for two minutes and it will all come back. What really requires manual intervention is a very few pieces of equipment.: I have an old laptop from 2019 at home. After replacing the panel in the master bedroom, it refuses to recognize the WiFi 6 on the new panel. All other devices are fine and it just spins around in circles. The solution is to update the wireless network card driver in the device manager. If the device really doesn't work, there is a way to avoid it - it must recognize the 2.4G SSID and just refer it to the old name. The specific compatibility ideas are as follows: Xiaomi router WiFi6 compatible article It’s the same as what’s written in it. When the old device doesn’t recognize WiFi6, leave a WiFi5 path for it. The panel AP side is more calm: The new panel’s WiFi6 is backward compatible, and the 2.4G frequency band will always remain open to older devices.
acceptance: Test each room one by one, don’t trust your body sense
The weekend after all four were replaced, I made a table and measured each room three times before and after the replacement to get the median. Numbers don’t lie:
| Room | Median before switching (Mbps) | Median after replacement (Mbps) | Equipment used |
|---|---|---|---|
| Master bedroom (farthest) | 186 | 412 | WiFi6 mobile phone |
| study | 215 | 470 | WiFi6 mobile phone |
| children's room | 243 | 488 | WiFi6 mobile phone |
| Dining room | 268 | 505 | WiFi6 mobile phone |
| Restaurant (old notebook) | 98 | 104 | WiFi4 old network card |
The most informative thing in this table is the last row: The old laptop has basically remained unchanged before and after replacement. Its network card is too old and cannot enjoy WiFi6. Replacing the panel is a waste of time. Therefore, only when new equipment is tested during acceptance, the gap can be seen, and when old equipment is tested, the wrong conclusion will be drawn that "replacement is in vain". The speed measurement method itself is also very particular. Take the median of three times and don’t test during the peak download period. These are what I will do. The article about speed test posture I’ve written it before, so I won’t repeat it. In addition, every time I change a panel, I will walk around the room twice with my mobile phone to see if the signal switching is smooth - whether the roaming between panel APs can be smoothly connected is related to the 11k/v setting of the AC. This is what I am doing. The article about 802.11k and v There are complete records.
The last step for acceptance is to check the online list on the AC management page: All four panels are online, the firmware versions are consistent, and the number of clients on each panel is normal. With four panels in my house and the ceiling AP in the living room (that one is still WiFi 5 and has an access port, I will save it for replacement next time when the budget is enough). There is no shortage of five APs in the list. Firmware unification deserves special mention: The factory firmware of new panels is often not the latest. When pushing all with one click on the AC management page, the new and old panels were upgraded together. I chose a time in the morning when no one was using the Internet to do it. The five units were restarted one by one. This process took about ten minutes. AC all-in-one machine inspection article Demerit.
ending: In any case, I advise you not to change.
After this replacement, the most intuitive change is that the mobile phone speed in the study went from just over 200 Mbit/s to 470 Mbit/s, and the TV no longer spins when watching 4K. But looking back, there are three types of families who think it is a waste of money to switch to this one. Category 1: broadband below 300 Mbit/s: The actual speed of the WiFi5 panel is more than 200 Mbits, which matches your broadband. The bottleneck is the broadband, not the panel. In the second category, the main equipment at home is a three- to five-year-old mobile phone or computer.: The device does not support WiFi6, so no matter how new the panel is, it will be useless. Change the device first and then talk about the panel. The third category is that the panel AP has only been installed for a year or two and has not purchased any new equipment.: There is no profit side, so it’s not too late to replace the equipment if it really can’t keep up.
On the other hand, if your family is in a similar situation to mine - gigabit broadband, a WiFi6 mobile phone or a large-screen TV in the past year, and a panel AP that has been in service for more than three years - then this replacement is very cost-effective.: The AC all-in-one machine does not need to be moved, and the network cable does not need to be moved. It only costs four panels and takes twenty minutes per room. If your panel AP has a problem, or the weak current box needs to be wired, you can also do it together. It is best to check the network port section when the panel is removed. When I took apart the piece in my study, I found that the crystal head was a little oxidized and darkened, so I pressed one head heavily. This judgment method is Panel AP maintenance article It's written in it. One sentence to end: The replacement of panel AP is "local surgery" rather than "general anesthesia". It is moved from room to room, with the same name and password, and there is no sense of transition of the whole family's equipment - this method of play is known to everyone who uses it.
