Message board

Author:SHUNOT• Published on:2023-08-26• Category:Uncategorized• Comments: ( 226 )

blog is built on personal interests. Collected and summarized wireless router settings__ HTML21__， Wireless Routing Lightcat __ HTML41__, Lightcat, 192.168.1.1_HTML55____ HTML56__ Some experience in basic knowledge fault handling, I hope it will be helpful to everyone!

Spam comments are not welcome on this blog, please do not vent here! Frequent comments are automatically blacklisted. healthy and meaningful comments and comments, I will take the time to reply ! If you want to see a reply as soon as possible, you can fill in your email address when commenting and commenting, and my reply will be sent to your email!

Comment List

Shao ShuaiReply

#73

How to connect the RG201O-CA to a TP-LINK wireless router

2013-07-18 05:58

EagleReply

#72

I would like to ask, my optical cat model is ZTE ZXA10 F420, and I want to enter the administrator to turn on the routing function. I want to ask, the article on the site is applicable to this model of light cat

2013-07-07 08:57

IceReply

@Xiaoying: First of all, the super administrator password has not been changed. Search for F420 is all relevant.

2013-07-07 18:35

studentReply

#71

The router login address has been modified, please ask how to scan out the correct login address ipconfig The information seen is incomplete

2013-06-20 21:24

Wireless routersReply

@Student: Looking at the status of the network card, the gateway is generally the login address of the router. How can ipconfig view be incomplete? This is incomprehensible unless the IP is not obtained

2013-06-23 18:14

zjchxjReply

#70

Device model: I-240W-Q Device Identification Number: A8AD3D-3B300A8AD3D2A377C Hardware version: I-240W-Q_V1B1 Software version: GX240WQV2.0.0 After I decompressed. Modify and then package it back and restore it. As a result, the data is all messed up. I don't know if it's a problem of not packing the tools. The original decompression is only a 00000014.dat. After packing, it becomes 00000000.dat Do you know how to fix it?

2013-05-20 22:39

IceReply

@zjchxj: I don't know what you packed back for, is it to modify the number of units? If so, it is not necessary. There is no modification. If you really want to package and upload, try other tools.

2013-05-20 23:07

zjchxjReply

@Bing Ling: Packing back is to modify the number of units. After modification. Put the USB back. After restarting. Device model: I-240W-Q Device Identification Number: A8AD3D-3B300A8AD3D2A377C Hardware version: 1.0 Software version: 1.0 It became like this. Unable to connect normally. Other tools. For example? If not. How to modify the number of units. Because TELNET itself is down. I really don't know how to do it: I want to use the wireless that comes with the light anchor. However, there is a limit to the number of units. Mobile phones and tablets are old and can't go online. Just connect.

2013-05-21 00:32

Pray for many ble...Reply

@zjchxj: Try using the gz compression tool to compress, many telecom upper-level equipment also limit the number of units, and sometimes it is useless to modify it.

2013-05-21 01:15

zjchxj

@Pray for more blessings: used, can't be decompressed. Just OFFZIP works.

2013-05-21 02:41

ratReply

#69

The landlord is a master, I would like to ask you some questions by phone or email. Can you give me a contact information or email? My contact information Q: 16147273

2013-05-18 09:52

IceReply

@Mouse: Hello, there is my contact information in the sidebar.

2013-05-19 19:10

jsy0620Reply

#68

Thank you for sharing so much useful knowledge with you, I would like to ask if the new version of I-240W-Q wants to break the limit of 4 units, how can the modified ctce8_I-240W-Q.cfg file be restored to the machine? Management--USB interface "Quick Restore" tick, the interface only has the button for backup configuration, ask for advice!

2013-05-18 00:09

IceReply

@jsy0620: Plug in the USB flash drive, restart the optical cat and the profile will be automatically restored.

2013-05-19 19:09

boyReply

#67

Why can't the 8245 customized by Telecom brush the original firmware, is there any solution?

2013-05-16 01:44

IceReply

@Boy: Yes, it can be brushed, but some functions cannot be used.

2013-05-16 02:22

boyReply

#66

Hello, how to flash the ordinary firmware of the 8245 telecom version

2013-05-14 20:27

worldReply

@男孩: Friend, https://www.shunot.com/?post=114 this is an article introducing methods. I don't know if it can be used.

2013-05-15 02:38

boyReply

#65

Hello, ask, do you know how to upgrade the firmware of the telecom version of 8245? Enter the following URL in the URL address bar to bring up the upgrade page: http://192.168.1.1/html/management/firmware.asp, it doesn't work if you lose this

2013-05-14 07:56

IceReply

@男孩: https://www.shunot.com/?post=114 This has an introduction

2013-05-15 02:41

youngReply

#64

I use the router in the school dormitory, I use PPPOE dialing, every time I use it and unplug the wireless, it is always very slow to connect again, I used to plug it in within five minutes, and now I can't connect to the Internet for half an hour, how to solve it.

2013-05-12 22:37

IceReply

@Young: Generally, it's good to start the cat again.

2013-05-13 19:18

xrz2088Reply

#63

Hello. I want to trouble you, can you find the firmware for HG8240R non-telecom version? Thank you

2013-02-28 19:28

IceReply

@xrz2088: Sorry, not yet.

2013-02-28 22:55

qliReply

#62

Hello! I'm new to this. Yesterday I connected to the wireless router with a optical cat network cable, and it also followed the 192.168.1.1. (I am designing with a mobile phone). I couldn't use it all the time, and then I took the router away, and there was no network when I used the optical cat to access the Internet.

2013-01-31 05:20

greenhornReply

@qli: It may be that the wire is not plugged in

2013-01-31 22:57

ZTEReply

#61

ZTE ZTE 531B is brushed into W300R (V1.0.3.U06B full-featured version firmware), it can be automatically dialed, there is no problem to watch ITV desktops access the Internet through the Internet, laptops and mobile phones can connect to WIFI signals but cannot access the Internet, MAC address is added to the cat, and the IP address gateway DNS address is set on the mobile phone is not good. How should I set up wireless Internet access on my mobile phone?

2013-01-29 03:06

Summer and autumnReply

@ZTE: First of all, it is determined that it is the cat automatic dialing. The setting mode is bound to the wireless port.

2013-01-29 17:51

IceReply

@Xia Qiu: You need to bind SSID1 to succeed

2013-01-30 18:45

ZTEReply

@Bing Ling: Bing Ling, hello! I divide wired and wireless into two LAN groups with two static IP addresses. Specifically, the itv and four wired Ethernet1~4 are set on the LAN group 1, the IP address of this group is set to 192.168.1.1, the WLAN is set to LAN group 2, the IP address of this group is set to 192.168.2.1, and the subnet mask is 255.255.255.0. Then set the IP address of the access point on the mobile phone to 192.168.2.x, the subnet mask 255.255.255.0, the gateway 192.168.2.1, and also set the address DNS (the DNS server value found from the local network connection information of the desktop computer), and you can access the Internet wirelessly. The above mobile phone is a 5800W Symbian system. In addition, the laptop (winXP) can also be set up to access the Internet smoothly. The problem now is: the Android phone (sansungS7652) does not have wireless Internet access with the same settings. My relative's win7 system notebook is also set up and cannot access the Internet wirelessly, and it is not even possible to search for the WIFI access point. Bind the MAC addresses of all phones and laptops to the SSID. What other places need to be set up?

2013-02-02 08:52

Ice

@ZTE: There is a limit on the number of devices. You can use it normally in the front. The problem is: 1. Exceeding the connection limit. 2. Android phone to set up.

2013-02-02 20:47

NONOReply

#60

I can't get it for a long time, so I ask for help

2013-01-29 00:41

IceReply

@NONO: Try using a generic password, if it doesn't work. Find your broadband provider and ask for a super password.

2013-01-29 01:03

NONOReply

@Bing Ling: Can you still ask for a super password? I can't connect to my wireless router and don't know how to tell if the router is broken

2013-01-29 19:02

IceReply

@NONO: Super passwords can be requested from broadband providers. Judge whether the router is broken, test whether the ports are normal, and whether the router management interface can log in. Whether the wireless signal is normal (some wireless routes can only receive signals within one meter after a problem)

2013-01-29 19:12

NONO

@Bing Ling: The interface can be logged in I tried using the optical cat link wireless router method on the Internet, but I can't connect to the Internet

2013-01-29 19:14

Ice

@NONO: No network cable connection

2013-01-29 19:17

NONO

@Bing Ling: The network cable is definitely not wrong I have tried a lot of methods in the settings

2013-01-29 19:18

NONOReply

#59

Hello! I want to crack ZTE f420 according to the tutorial Input is not possible The prompt did not find the file, I don't know what is going on, please can you answer, or tell me QQ online help, or add me QQ 58 #114 #28

2013-01-28 20:30

Summer and autumnReply

@NONO: Do you want to get a super password or break the 4 machine limit? It is difficult to find documents in the 4 restrictions.

2013-01-28 20:48

NONOReply

@Xia Qiu: I want to crack the super code according to the online method, but I can't find the file

2013-01-28 20:58

Summer and autumnReply

@NONO: If you only need to get the password, you don't need PJ, you can directly click on http://192.168.1.1 /web_shell_cmd.gch, Enter in the small box: sendcmd 1 DB p UserInfo, and then look at telecomadmin, and below is the super password Reference: https://www.shunot.com/?post=110