1. Current Location: Home >  Comprehensive classification >  How to choose an AC all-in-one machine? After installing two apartments, I straightened out the parameter list.

How to choose an AC all-in-one machine? After installing two apartments, I straightened out the parameter list.

Full flow chart of AC all-in-one machine purchase and background settings: Account account, POE power account, six-step setting and roaming switch

It has been more than two years since I installed the AC+AP in my new house. I have never had to worry about the AC all-in-one machine in the weak current box. The only time the study panel went offline was when I checked the line. The article about panel AP losing connection Wrote in. In October this year, the renovation of my cousin’s house entered the final stage of panel replacement. WeChat sent me a screenshot of the shopping cart.: 「Is it okay to just buy this? 」I clicked on it and saw a machine labeled "POE Router" with four panel APs hanging underneath. Further down, the customer service also recommended an eight-port POE switch. I said stop, don't pay yet, half of the money here is wasted. After helping her to match this set, I turned around and dug out the set I had back then and read through the instructions - it turned out that I had bought the right set for the first time by mistake. This article summarizes the purchase of AC all-in-one machine and the settings to be done after getting it. If you have a clear calculation of the number of ports and power, you will basically not make a wrong purchase. .

First distinguish: AC integrated machine, POE switch, bare AC, these three are not the same thing

I was also confused by these three words when I was doing my first set of renovations. Breaking it down is actually very simple.: AC It is the brain that manages the AP and is responsible for uniformly sending WiFi names, passwords, and channels, making the four panels look like a whole. ; POE It is a hand that supplies power to the AP through a network cable. One cable transmits data and electricity. ; routing It's just regular dial-up forwarding work. On the market, those that put these three into one case are called AC all-in-one machines, and some are also called POE routers. One thing has two names.

Trapped in customer service talk. The "POE router" in my cousin's shopping cart itself has four POE ports, and the customer service also recommended an eight-port POE switch on the grounds that "it will be convenient to add APs in the future." Later, I checked the parameter table to confirm.: In her four bedrooms and two living rooms, all four panel APs are fully plugged into the all-in-one machine. The switch is completely redundant - unless she plans to hang another ceiling AP in the living room, she will only need the expansion of the switch. In the same way, there is "naked AC", which is a pure controller with only management, no POE, and no routing. It is basically untouchable for home use and will only be used in projects with more than a dozen APs on several floors of a villa. My own machine is a TP-LINK TL-R479GPE-AC, with a router AC and eight POE ports. I bought it purely because the customer service said "this machine has enough capacity", which was a mistake.

first account: Number of mouths. Count APs first, then count uplinks

I also got distracted for the first time when it came to counting my mouths. Each of the four bedrooms in my cousin's house has a panel AP. It seems that four ports and four APs are just right, but there is still a cable in the weak current box for the optical modem to go into the all-in-one machine, and the NAS also needs a cable, and these two ports also have to come out of the all-in-one machine. Four plus two equals six, and that all-in-one machine with four POE ports is not enough. The final plan is: The four panels occupy four POE ports, and the optical modem and NAS use the other two ordinary LAN ports on the all-in-one machine - so be sure to check them before buying. Number of POE ports and Number of common LAN ports Count them separately. Don't just read "8 ports" on the parameter page. Look carefully at which ones have POE.

There is another one that leaks easily: The ceiling AP in the living room. The set in my new house has four panels, a living room ceiling, and five POE devices. The machine has exactly five POE ports, which are fully used. If I had bought one less port, the one in the living room wouldn't be able to connect to it. There is another accounting for the routing and avoidance of ceiling APs. Ceiling AP installation article I have written about it in detail here, but here I only mention one point when purchasing.: The number of APs is reserved according to "the number of rooms plus one", and the larger number is reserved for the living room.

second account: POE power, the total budget line in the manual is most easily ignored

Just because you have enough mouths does not mean you can carry it. Each AP consumes electricity. The power consumption of a panel AP is about five to eight watts, and the ceiling AP can reach more than ten watts depending on the model. There will be a "Total POE power supply power" marked on the parameter page. For example, my unit is marked 53 watts. It sounds very big, but one point with eight ports would be very stressful - if all eight ports are plugged into the ceiling AP, each of the ten watts will cost 80 watts, which is excessive. For my cousin's plan with four panels and an eight-port switch, I also checked the POE budget of the switch. It turned out that 65 watts is more than enough with four panels, so I approved it.

The symptoms of insufficient power are very subtle: It's not that it can't light up, it's Good times and bad . A certain AP goes offline in the middle of the night and comes back during the day. Even restarting the machine does not solve the problem. It looks like a line problem, but in fact the total power is exceeded, and the machine takes turns to lose one or two ports to protect itself. So when I was configuring the second set, I copied down the nominal power consumption of each AP and added the total, leaving a 30% margin compared to the total budget of the machine. This five-minute action can save you a whole night of troubleshooting later.

First time setting up: Don't be in a hurry to fill it up, put the frame together first

Don’t plug in all the APs before you get the machine. My order is: The all-in-one machine is powered on independently and connected to the backend. Change the administrative password first ——Many machines are still admin when they leave the factory. This is the same as the password logic of optical modem. The machine password in the weak current box is the key. The article on sorting out weak current boxes It was mentioned in the book that keys should be written down on paper. Then set up broadband dial-up, confirm that you can access the Internet, and then plug in APs one by one.

The key to inserting AP is to "change the name one piece at a time". After the AP goes online, it will appear in the online list in the background. The default name is often a series of models or "AP-01". At this time, immediately change it to a comprehensible name such as "Master Bedroom Panel" or "Study Panel". Insert one piece at a time, change the name of one piece, and if there is a problem, you can immediately identify which room it is. ; If you plug them all in at once, there will be a row of "AP-01" to "AP-05" in the list. To check the numbers on the spot, you have to use your mobile phone to test the signal and guess one by one. I suffered this loss in my first set. I found out after half a month that the names of the study room and the second bedroom were reversed. The grouping was also established smoothly, and the rooms facing south were grouped into one group. If the channels were staggered, they would be adjusted according to the group later.

Roam those two switches: 802.11k and v, opened easily

What AC+AP is better than a bare router is roaming, but the default settings may not be fully enabled. Look for "Wireless Advanced" or "Roaming Settings" in the background. There are two switches.: 802.11k and 802.11v. The former allows the mobile phone to know which APs are available nearby, while the latter allows the mobile phone to negotiate among APs to switch to them. My station only had K turned on but not V by default, while my cousin's had both turned off. The most intuitive change after opening it: When I walked from the living room to the master bedroom with my mobile phone, the switching was reduced from the original two or three seconds to almost no effect. There is usually an RSSI threshold in the settings page, which is "how weak the signal is in dBm to remind the phone to move." For both sets, I set it around minus 65. If you switch it too early, it will jump back and forth, and if you switch it too late, it will wait until there is no signal.

By the way, channel and power. If four panels are crowded on the same 2.4G channel, they will fight with each other. There is usually an "automatic optimization" button in the background. Clicking it will stagger the channels according to room groups. I recommend manually adjusting the power: The two adjacent panels are fully powered, but the signals from the two panels are fighting in the middle area. If one of them is downgraded by two levels, the boundary will be clean. In scenarios where there are so many devices that slow down the Internet speed of the whole family, the root cause is often at the signal layer rather than the broadband. The article about setting up separate WiFi for devices I talked about the layered idea here, and the same applies to panel AP.

Semi-annual inspection: Online listings and firmware

You don’t need to keep an eye on it every day, but it’s worth going backstage and reading two pages every six months. The first page is the list of online APs. Are all four panels on? Are any of the panels frequently disconnected and then self-recovered? The one that often goes offline and comes back is 90% likely to be caused by oxidation of the network cable crystal head. Change the head as soon as possible. If it is completely disconnected, you will have to get up in the middle of the night to investigate. The second page is the firmware version. AP firmware upgrade is different from router. It’s all pushed from the AC backend with one click. , the upgrade will restart the APs one by one, so do it in the morning when no one at home is using the Internet, and restart the four panels one by one, which takes about ten minutes.

During the inspection, take another look at the machine capacity. The nominal capacity of AC all-in-one machines is generally too high. The actual steady state is 60 or 70 units when the nominal capacity of AC all-in-one machines is 128. This problem cannot be avoided when there are too many smart devices in the whole family. The article about 49 smart homes The accounts have been settled. When my cousin's finely decorated house was delivered, the master had about forty smart devices hanging under the temporary network. The article about losing connection after changing network It saved her once - so when I equipped her with an AC all-in-one machine, the amount of the machine was doubled, so that she would not be left wondering two years later after adding more equipment and getting stuck.

ending: Three accounts and one table

After helping my cousin match this set, I compiled the purchasing decision into a check list and followed it from top to bottom.:

Purchasing steps What number to look at my reference value
Several POE ports Add one to the number of rooms (leave the ceiling in the living room), and then see if the ordinary LAN port is enough for the optical modem NAS Four bedrooms and two living rooms: starting with five POE ports
Calculate POE power Add up the power consumption of each AP and compare it with the total budget of the machine, leaving a 30% margin. Panel 6 watts x 4 + ceiling 11 watts, budget at least 40 watts
Nuclear belt capacity Cut the total number of devices in your home in half and see the nominal value. Standard 128 units are used for 64 units.

I also remember the actions in order after buying it.: Change the management password, set dialing, change the name of one plug and one plug, turn on 11k and 11v, click on automatic channel optimization, and lower the power by one level. The initial threshold for AC+AP is indeed a little higher than that of Mesh. This was also the point where I struggled repeatedly in the selection comparison. How to choose between AC+AP and Mesh The complete trade-offs were written in that article. But after the skeleton was put together, it was the most worry-free networking method I have ever used. The machine in the weak current box has not been restarted a few times in more than two years. The WiFi name in the whole house is the same, and it is the same network wherever I go. The first set was correct because of luck, the second set was calculated correctly. This article is about that account.

Read More


Copyright Notice Scan to read on mobile
All Rights Reserved: 《SHUNOT》 => 《How to choose an AC all-in-one machine? After installing two apartments, I straightened out the parameter list. 》
Article URL: https://www.shunot.com/en/zhonghe/1577.html
Unless otherwise stated, all articles are original by 《SHUNOT》. Reposting is welcome! Please indicate the original URL when reposting, thank you.

Contact Us

Online Consultation: Click here to send me a message

WeChat ID: master_135

Scan to follow