1. Current Location: Home >  192.168.0.1 >  The router gets stuck every few days, but after restarting it becomes normal again. I have been diagnosing this problem for a month.

The router gets stuck every few days, but after restarting it becomes normal again. I have been diagnosing this problem for a month.

Triage chart of four causes of router jamming every few days

I have used the Mercury D191G at home for more than three years, and I have developed a bad habit in the past two months.: The internet gets stuck every few days, my phone spins around while scrolling through videos, and the screen cast stops. I unplugged the power and restarted it. After a minute, the phone came back. Nothing wrong. But after three or five days, it happens again. This cycle of "just restart and it'll be fine again" is the most annoying. Please report it for repair. It was fine when the technician came to your door. ; No matter, the family complains every day.

I simply use it as a medical record book and write down all the times I got stuck.: What time did it happen? How many devices at home are online? What are the numbers in each field in the background? Is the body hot to the touch? After a month is full, I will look back. This kind of card that occurs every few days is not one kind of disease at all, but four kinds. The treatment methods are very different. Only one of them is suitable for automatic restart, and the other three are bad things if they set a scheduled restart. Let’s talk about them one by one.

First look at the three fields in the background to eliminate “fake cards”

Before starting the triage, enter the moment when you are stuck. 192.168.0.1 Look at three things: Running time, number of connected devices, and traffic statistics. This step is to eliminate "fake cards" - the ones where the problem is not with the router at all.

I almost misdiagnosed it the first time. That night, the whole family cast a screen in the living room, but it was too stuck to watch. I went backstage and saw that there were 58 devices, but there were only about 20 devices in the house. Looking through the device list again, what came out were two neighbor’s old mobile phones—the WiFi password hadn’t been changed in three years, and someone had already used it. The network device is occupying the bandwidth. No matter how you restart it, it will be in vain. After restarting, it will automatically reconnect, and it will be stuck after two days. This "just restart" is an illusion. In fact, the network device happened to not be transmitting anything at the time. The way to deal with it is to change the password. Close the door first. I was there before. The offense and defense of blocking the network and changing the MAC to connect back to the network The complete blocking method has been written here and will not be expanded upon here.

The traffic statistics field is also worth looking at. If no one is at home during the day, but the router is running dozens of gigabytes of traffic in the middle of the night, it is because the camera is pushing video to the cloud or there is a device uploading it in the background, and it has nothing to do with the router itself. My D191G had a scary amount of traffic in the middle of the night. I checked for a long time to find out whether the cloud storage switch of the living room camera was turned on by mistake. I am here to check the order of this kind of "fake cards". The article about the upstream bandwidth being eaten up As I wrote in the book, first identify who is eating before taking action.

After eliminating the network interference and bandwidth, the router still suffers from lag, and then it is the router's own fault. The following four types are what I actually encountered in rotation during that month.

The first type: The connection ledger is too thick, restarting is the right solution

The router keeps a ledger in its memory.: Every time a device opens a connection, it remembers "where to send this data." With so many smart devices at home, the debt is frighteningly thick. I went into the backend at 9pm when my whole family was online and saw that about 20 devices can handle 1,500 to 1,500 connections. When the memory of the machine is too small, and the account book cannot be written, the account will be lost and stuck. This is manifested by the screen spinning in circles and the device going offline. After restarting, it will be fine again - restarting is equivalent to tearing up the account book and re-entering it.

The characteristic of this disease is that "the effects are immediate and regular after restarting." The time I recorded my illness was very neat.: It happens almost every Thursday night, because the whole family uses a lot of equipment on weekends, and the account book is full by around Thursday. It is also the only one of the four diseases that should be set to automatically restart.: Mercury's backend hides this function in "Automatic Cleanup", which doesn't even have the word "restart" in the name. The official name is to automatically clear entries and cached data, and the cleaning process will be briefly restarted. ; The entrance to Tenda is in the system tools, ask the device to restart or customize the restart. How to set the specific paths and frequencies of the two companies? Mercury's automatic cleaning and Tenda's system tools restart regularly I have written them separately, so just copy them.

A piece of advice about frequency: Once a week is enough, don’t be greedy for once a day. I tried cleaning it every early morning, but the camera with close signal at the door went offline and struggled to reconnect for a long time, and then went offline the next day. The cache does not accumulate that quickly, and there is no difference between clearing it once a day and once a week.

There is also a joint judgment: If you have more than 30 or 40 devices at home, don’t just expect to restart them. If the memory ledger is thick enough, restarting will only extend your life. The sub-network segment of this sub-network segment, the machine that should be replaced with a large memory machine, Router memory account and Actual measurement of machine capacity Here is how to determine the water level.

The second kind: The channel is crowded, restarting is an anesthetic, not a medicine

In the second month's records, I found that there were several times where the card didn't match the interval pattern at all - it was committed on Tuesday, it was committed on Sunday, and once it was committed on two days in a row. This irregularity is probably not caused by the machine itself, but by the wireless environment. I took out my mobile phone and installed a WiFi analysis app to check the channel occupancy. Four neighbors' signals were connected to the 2.4G channel 6 in my house. At ten o'clock in the evening, their children were playing games, and my house was crowded.

Channel congestion is a problem that can only be alleviated by restarting for a few dozen minutes. Because after restarting the router and re-broadcasting, the number of connected devices was reduced for a moment, and the crowding was temporarily stopped. When everyone started to connect back one after another, they were still crowded on the same channel. The correct solution is to manually change the channel: For 2.4G, look for the three numbers 1, 6, and 11, pick the one that is currently the emptyest, and pin it. Don't turn on automatic—automatic only picks it once at the restart, and then it won't move when the external environment changes. The pit of channel 52 In that article, I recorded a case where the 5G channel automatically jumped to the DFS channel. The principle is the same. A simple way to determine whether it is a channel problem: When the WiFi signal is stuck, check the number of WiFi signal bars on your mobile phone. If it is full but the network speed is poor, it is most likely because it is crowded, not because the signal is weak.

By the way, channel and signal strength are two different things. If you feel that the signal at home is weak, go to the backend and adjust the signal strength level to a higher level. The default switch is not the through-wall level. Adjusting it to the strongest can increase the signal strength by two dB. This is a zero-cost matter. I have written about the differences between the three levels in another article. When it is still weak after adjustment, it is time to change positions or add nodes.

The third kind: Overheating, restarting covers up the heat dissipation account

The most distressing period in the record is the two weeks in July: It started to get stuck at 3pm, got worst at 8pm, and got smoother again in the middle of the night. Touching the fuselage is hot. This is overheating, not because the program is messed up, but because the hardware cannot sustain the power supply at high temperatures. The reason why the restart is "good" is very real - the minute the machine restarts, the load returns to zero and the temperature drops a bit. When it continues to run, the temperature climbs back up and the card is still stuck. Therefore, the automatic restart of this disease is equivalent to taking antipyretics regularly without even looking at the thermometer.

The way to deal with it is all physical work: Move the machine out of the weak current box, place it vertically, keep it away from the front and back, and stay away from the heat-producing optical modem. My D191G was moved from the drawer of the TV cabinet to the open door of the shoe cabinet, and it changed from "once a week" to "once every three weeks." If your machine is in a weak current box, it is stuck in the summer and not stuck in the winter, that's basically it. The extreme version of overheating is aging hardware: The high-temperature characteristics of the capacitor deteriorate. It will break down when the weather is hot, and it will automatically recover in autumn. This is a sign of the life of the machine. This is how my retired old machine completed its final journey. Five signs of aging There is a complete judgment method in that article. If two signals appear, don't repair it and just prepare to replace it.

A counter-intuitive reminder: Don't put a heat sink on the router or use a fan to blow it. A home router has a small amount of heat, so it is enough to move it to a location for ventilation. Instead, the SMD fan tends to draw dust into the body, which accumulates dust and then overheats, making it worse.

The fourth kind: Aging power supply, the most unfair kind

The last one is the most gloomy, I almost fell on it myself. At that time, the machine restarted more and more often, from once a week to once a day. I judged it to be aging and put the new router in the shopping cart. When I was packing up the machine, I touched the power adapter - it was ridiculously hot. Pull out the multimeter and measure it, the output is only 9.8V, nominal 12V. Many "routers are aging" because the adapter is aging first.: When the output voltage drops, the router runs on the verge of undervoltage, restarting or freezing at every turn.

This disease is characterized by "restart intervals getting shorter and shorter." The intervals of the first type are regular, the third type follows the temperature, and the fourth type worsens visibly to the naked eye. Verification is also simple: Use a multimeter worth about 40 yuan to measure the adapter output and compare it with the nominal value. If the voltage is not up to par, replacing it with an adapter of the same specification costs tens of dollars, but the machine itself is not broken. I have practiced using a multimeter to measure the voltage of sockets at home. How do I read the 100-240V input line and output voltage on the adapter? The power adapter article Full instructions are included. The rule of thumb is to measure the power supply first and then judge the machine’s age. Thirty yuan can avoid unnecessary consumption of two hundred yuan at a time.

By the way, the voltage at home is really unstable (in old communities, the lights dim when the air conditioner is turned on). The criteria for judging whether to need a voltage stabilizer are also in this article. Most families cannot reach the bottom line of network equipment, so don't spend money arbitrarily.

Four kinds of diseases are correct in one table, don’t rely solely on restarting to deal with them

After a month, I put the characteristics and treatments of the four diseases into a table. When getting stuck, check your watch first and then take action.:

Disease type The pattern of illness Restarting doesn't work correct answer
Connect the ledger thick Regular intervals, about a week It works, it works immediately Set to automatically restart once a week
Channel is crowded Irregular, most frequent at night Anesthetic, dozens of minutes Manually pin 1/6/11 empty channel
overheat Just follow the temperature, it will get stuck in the afternoon Antipyretics can't cure it Move the location to ventilate it, and replace the machine if it ages.
Power supply aging The intervals are getting shorter and shorter It's becoming less and less effective Multimeter output, change adapter

The fixed actions for you are just four steps.: Don’t rush to restart when stuck. Go into the background and take a screenshot and note down the number of devices and running time. ; Remember it three or five times in a row, and the patterns will emerge. ; Locating disease types on the table ; Treat the problem according to the situation, set the setting when it is time, move the machine when it is time to move it, and change the adapter when it is time to change the adapter. Restarting itself is also very particular - restarting after a power outage, restarting in the background, and restoring to factory settings are three different things. If used incorrectly, it will cause trouble. The difference between the three things I wrote a separate article, so I gave it a quick glance before I started.

There are two other things that are easily confused with "the more you use them, the more stuck they become." I will directly eliminate them for you here.: Cutting off the Internet on time in the middle of the night is not a machine disease, it is the work of parental control or WiFi timer switch ; After a long time, the scheduled tasks are running randomly. It is because the router has no battery and is powered off and reset to zero. Time returns to zero There are practices. Check these two for five minutes, don't go around the machine.

Finally, let’s talk about my D191G: After triage, it is the first type plus the third type - the ledger is thick and the shoe cabinet is stuffy in summer. I set up automatic cleaning for Thursday morning, moved the location, and no card issues occurred again in two months. This problem is not difficult. The difficult thing is not to use restart as a panacea. The patterns covered by restart are the truly valuable clues.

Read More


Copyright Notice Scan to read on mobile
All Rights Reserved: 《SHUNOT》 => 《The router gets stuck every few days, but after restarting it becomes normal again. I have been diagnosing this problem for a month.》
Article URL: https://www.shunot.com/en/192-168-0-1/1583.html
Unless otherwise stated, all articles are original by 《SHUNOT》. Reposting is welcome! Please indicate the original URL when reposting, thank you.

Contact Us

Online Consultation: Click here to send me a message

WeChat ID: master_135

Scan to follow