Home • All articles by author SHUNOT - Page 4

Problem description: The official latest firmware used by TP-LINK7260V1 always drops from time to time, sometimes it drops for 1 and a half days, sometimes it drops for a few hours, sometimes it just drops, and it drops again after a few minutes. 🛠️ Recommended Steps to Fix Step 1: Basic Troubleshooting Check the temperature of the power adapter - if it is hot, it is recommended to replace it with a higher power one (such as 12V2A) Improve heat dissipation - Raise the router to avoid placing it in an enclosed space Replace the network cable - Try to replace the network cable connected to the optical cat Observe the light cat indicator -......

the login entrance address of the Xiaomi router is: 192.168.31.1 and miwifi.com Many users buy Redmi routers or Xiaomi routers, and want to use their mobile phones to open the 192.168.31.1 login entrance but don't know how to operate. Preparation: Phone: WiFi connected to the Xiaomi router (whether it is a 2.4G or 5G signal). Admin password: The router's admin password......

192.168.2.1 login entrance is the IP address used by China Telecom, many telecom broadband users use the telecom router given by China Telecom, some users want to use their mobile phones to log in to the telecom router management background to modify the wireless WiFi password but don't know how to operate, the following is a detailed mobile phone login to the telecom router (default address: 192.168.2.1) to change the WiFi password graphic tutorial. Necessary preparations: Phone: Make sure your phone is connected to the wireless WiFi signal of your current telecom router, which ......

Ordinary user login gateway: http://192.168.1.1/login.cgi2. Enter the URL to open telnethttp://192.168.1.1/enableTelnet.cgi you can see the account and password, but there is no application button, the default is no application button, to f12 debug the console to break to line 194 if ( cUserName != useradmin ) { document.wri... ...

First of all, buy accessories online (see the picture below), and at the same time 6 yuan two eMMC master controls, which are used for USB flash drive transformation. Get to the point: 1. Remove the 8G eMMC on the motherboard, solder it to the eMMC master, plug it into the computer, and use Winhex to back up the original system into a bin file for later use. 2. Solder the eMMC 64G (by the way) on the C and D sides of the eMMC live seat, and the A and B sides of the live seat on the motherboard 3. Connect the 64G EMMC soldered in the live seat to the adapter board and USB card reader, and write on the computer......

Problem description: I am using Merlin 3004.388.11, and I will suddenly be unable to connect to the Internet when I use it, and I can't ping the website after connecting to the router ssh, but the online status still shows that I am online, and I need to reapply the settings to trigger the replay to restore the network, so that it can be restored. It is a problem that occurs after replacing the optical cat: because of the upgrade package, the telecom first replaced the tewa7501v, and when using it, it will encounter a light signal flashing light without a network, and it will take a while to recover....

Many friends don't know how to set up 2.4G and 5G frequency bands on their home routers, and I will sort out the differences between 2.4GHz and 5GHz Wi-Fi frequency bands and setting suggestions for you in detail. 📡 2.4GHz vs 5GHz Core Difference Comparison Features 2.4GHz 5GHz Wide coverage 🟢, strong 🔴 wall penetration ability Narrow, weak wall penetration ability Transmission speed 🔴 up to about 150-600Mbps 🟢 Up to 1.3Gbps+ (Wi-Fi 6 can......

⚠️ Pre-warning Risk warning: This operation may cause the optical cat to become bricked, the operator may be remotely locked, or the warranty may be lost Applicability: Mainly for ZTE optical cats (such as F650, F673AV9, F677V9, F1855V2 and other models) Legal compliance: Only applicable to devices legally owned by individuals, unauthorized operation may violate the service agreement Step 1: Preparation Project Description Physical preparation Unplug the fiber optic cable, prepare toothpicks/card pins (for reset) Network environment The computer is directly connected to the optical cat LAN port through the network cable Required......

Get the nine-link light cat UNG153H get the super password is actually very simple Step 1: is to open telnet, the machine defaults to turn off telnet, and open the browser with the computer. Enter http://192.168.1.1/webcmcc/telnet.html in your browser to display Open Telnet Success!. Indicates that the telnet has been successfully turned on. Step 2: Connect the telnet with the tool. The account and password are used on the label on the back of the light cat......

I found that many friends are looking for AI assistants that can be automated without computer or mobile phone installation, and realize functions such as automatic reply messages, cross-app ticket grabbing, and regular group blessings. Let's share the 2 open source apps I found. The article will provide the download address of 2 APPs 01 Roubao (meat bun) An APP mentioned by netizens in the previous message, this Roubao (meat bun), can be used when installed. No computer, no cable, no technical background required. Open the App → Configuration API ......