-
I turned off the DHCP router with my hand. That night, the whole house was disconnected. I finally figured out the address pool and lease.
The IP address of every device in the home is automatically sent by the router's DHCP. I accidentally turned it off, but FamilyMart's WiFi is full but I can't get online. Address pool, lease, static IP—these terms are explained in one go, with three situations where you really should turn them off....
-
Turning on IPv6 on Xiaomi routers requires just a switch. 192.168.31.1 I have stepped on these three pitfalls.
Enabling IPv6 on a Xiaomi router is just a matter of switching it on and off in the internet settings under 192.168.31.1 Common Settings. But after I started it, I realized NAT6 is a fake public network, firewalls block incoming sites, and the optical modem even swallows V6. These three pitfalls are explained all at once. If you want to connect remotely to a NAS, read this article first....
-
Only after living in two buildings can I understand that broadband in residential areas and urban villages is cheap during the evening rush hour.
Renting for convenience: using the landlord's broadband, 30 yuan a month, 90 Mbps speed test at dawn, only 20 Mbps left at night. After living in two buildings, I got a thorough understanding of the community's broadband and the self-built urban village network: how to predict in advance, which tasks can't be done, and in what order to do self-rescue—all the numbers are here....
-
The router automatically dials the broadband account and fills in it once, and the on-demand connection pitfall has been avoided for a week.
Do I still need to connect broadband after installing a router? Enter your broadband account password into the router's backend to automatically dial the number, but if you set the connection mode to on-demand, your speed will fluctuate. This article clearly explains the four steps of PPPoE setup, the differences between three connection modes, and the boundaries of disconnection and redeang....
-
Mercury router uses two steps to open the guest network, and the NAS has not been opened by relatives.
When relatives come to your home asking for WiFi, directly giving the mainline password is equivalent to giving away the home key. My Mercury D191G has guest network enabled, and it can be set up in just two steps within melogin.cn. Guests can access the internet but can't access the backend or access the NAS. This article notes the setup path, speed limit values, and three pitfalls I've encountered....
-
The telecom optical modem is connected to two routers. After helping three families connect it, they can distinguish the three connection methods.
Want to connect both routers at home to the optical modem? First, remember that a broadband account can only dial once at a time; if both phones dial in at once, the lines will be skipped. I helped three families connect and went through all three connection pitfalls: optical modem router mode, bridge mode, and switch setup....
-
NAS shared folders allow everyone to open an independent account so no one deletes things by mistake.
The whole family shared one admin account, and my dad just dragged and removed his daughter's photos from three years ago. I set up an independent account for each person, with three directories in the public zone, private zone, and read-only zone, plus a permission matrix. The specific setup paths for Synology and Feiniu are all written here....
-
The router's beamforming is turned on and off for a week each, and the balcony WiFi depends entirely on it.
What does Router Beamforming mean? It's not about increasing power, but about focusing the signal toward your phone with multiple antennas. I tested both on and off for a week; the balcony speed differed by 60 Mbps, but the living room showed no change at all. This article explains the principle, the difference between explicit and hidden types, and how to choose a switch....
-
Restore Xiaomi router to factory settings, and the light on the card pin will turn orange after 5 seconds.
There are two ways to restore a Xiaomi router to factory settings: enter 192.168.31.1 and click on the backend, or hold the SIM ejector against the reset button for 5 seconds and wait for the light to turn orange. Before restoring, remember to write down your broadband account and WiFi password. For second-hand ones, you need to unbind and reset them at Mijia. If you reverse, you'll end up with a tail....
-
T568B is enough for the crystal head and wire sequence. Only after scrapping six of them can you understand the difference between four cores and eight cores.
Cable cable connectors yourself, and only the T568B cable is enough. I wrote down all the tool logs for crimping pliers, crystal heads, line testers, the eight-step crimping process, and the four cores that only 100MB and 8 cores are gigabit, along with five troubleshooting methods for crimping failures....

