-
I couldn’t install the plug-in after flashing OpenWrt, so I could completely distinguish between the router’s flash memory and memory.
Router flash storage and memory are often confused, and customer service even uses 16MB flash as a selling point to evade the issue. This article clearly explains how much flash storage can be installed and how much memory can be installed simultaneously. If the flash memory is insufficient, an error occurs halfway through plugin installation; if the memory is insufficient, it causes disconnections due to too many devices. By the way, I'll also offer advice on the configuration setup for a three-tier laptop....
-
Xiaomi signal amplifier costs RMB 49 for half a month. The three budgets will help you figure it out.
I bought the Xiaomi WiFi Amplifier Pro for 49 yuan, and after testing for half a month, the bedroom signal went from two bars to full, but the speed was less than half of a direct connection. This article presents the actual test numbers and target users for three routes: amplifier, converting old routes to repeaters, and adding Mesh sub-routers. After reading, you'll know exactly how much you should spend....
-
49 smart home routers, the WiFi version and the gateway version are more than a little different
The more smart devices you buy, the sooner or later the router won't be able to keep up. I counted all 49 devices at home one by one and realized that the WiFi and Zigbee gateway versions differ by several times in the router's slots. This article covers how to choose protocols before adding equipment, how to separate 2.4G private networks, and where to place gateways—all about network planning....
-
The WeChat video of router UPnP is blocked. I can’t understand it until I read the mapping list.
The UPnP switch in the router's backend—some online posts say it's a security backdoor and recommend turning it off. I messed up and turned it off, but after I did, I couldn't get through to WeChat video first. This article clearly explains what UPnP does, how to check the mapping list in the backend, which households should be closed and which ones to keep untouched, and how to manually forward and restore it after turning it off....
-
Tenda router speed limit, AC10 by IP segment, AX12 by device, tried both
How to limit the speed of a Tenda router? The new AX12 and other models directly fill in the uplink and downlink of devices at the device management point, while the older AC10 uses broadband control to fill in IP range rules, so you need to fix the device IP first, otherwise it's wasted. I've actually set up both interfaces, clearly writing out the unit conversion and the three pitfalls that don't work when limited. ...
-
I pressed reset by mistake and the telecom optical modem failed to connect to the Internet. I rescued it in three hours.
What should I do if I can't access the internet after restoring the China Telecom optical modem to factory settings? The night I accidentally pressed reset, the LOS red light flashed and WiFi name reverted to ChinaNet default. It took me three hours to fix it. This article clearly explains the order of what to lose or not to lose, judging by the light, waiting for ITMS automatic registration or manually filling in the LOD, and the bridging party handling the aftermath. In most cases, you don't need to call a master....
-
The NAS hard drive keeps waking up from hibernation. After checking the logs all night, I found that these are the only ones who secretly write to the disk.
NAS has the hard drive put into sleep but finds the hard drive keeps spinning? After setting it to 10 minutes of sleep mode, the hard drive was awakened more than 40 times overnight. I logged in with SSH and waited overnight using iotop, uncovering those who secretly wrote on qBittorrent, monitoring containers, and transcoding directories. This article clearly explains the troubleshooting order and which drives should be put to sleep....
-
Old Devices Won't Connect After Enabling WPA3: How to Choose Between WPA2 and WPA3
I switched to a new router and set WPA3 for encryption, but the old laptop, camera, and Kindle all couldn't connect to the internet. This article explains the differences between WPA2 and WPA3, how to set up hybrid mode, and which households should use WPA3, along with various brand setup paths and pitfalls to avoid....
-
Xiaomi router hides WiFi signal, and the sweeper cannot connect after hiding it
Xiaomi routers hide WiFi signals. In the WiFi settings of 192.168.31.1, there is a switch to turn off broadcasting, which can also be operated via the Mi Home app. But after hiding, your phone or computer won't automatically reconnect, and smart devices like vacuum cleaners and cameras simply can't find the network. This article goes through both the operations and the pitfalls....
-
I used an old router as a bypass router to advertise, and the first time I connected it, it paralyzed FamilyMart.
Bypass router means the main router continues its routine, while an old device has a network cable hanging nearby just to run ads for dirty work. I built one with a dust-collecting N1 box. The first time I connected, I forgot to turn off DHCP and crashed my FamilyMart network. This article explains the four steps of connection and the four pitfalls I fell into at once....

