Home • All articles by author SHUNOT - Page 84

  • TP-Link cannot access the Internet after a failed firmware update

    Hard reset recovery Steps: Find the RESET hole on the back of the router Press and hold the RESET button with a toothpick for 5 seconds until all the lights flash Wait for the router to restart (about 2 minutes) Reconfigure the router through 192.168.0.1 2. TFTP forced to flash the firmware Preparation: Download the official firmware of the corresponding model (TP-Link official website) Set the static IP on the computer: 192.168.0.100 Steps: Press and hold the RESET key while powering on, keep 1... ...

    2026-4-7
  • Synology DSM 7.2 Installation Guide: From Hardware Preparation to System Deployment

    Applicable scenarios This article is suitable for the following users: Technology enthusiasts with idle computers/servers Users who want to build personal cloud storage Users who have some knowledge of NAS systems Hardware preparation Recommended configuration Necessary tools USB flash drive of 8GB or more Black Synology boot image (such as Jun s Mod) DiskGenius (partition tool) Rufus (make a boot disk) Installation steps Stage 1: Make a boot USB flash drive Download Black Synology boot image (.img format) Use ......

    2026-4-3
  • TP-Link Archer C7 becomes bricked after firmware upgrade, the red light is always on to save the brick

    Problem Diagnosis The TP-Link Archer C7 router has a solid red light after a failed firmware upgrade, which is a typical bricking phenomenon. A solid red light usually means: The router bootloader is still working The main firmware is corrupted or lost It can be repaired through recovery mode Solution: Solution 1: TFTP recovery method Preparation: A computer A network cable A TP-Link official firmware file (.bin format) Steps: Set the computer IP to......

    2026-4-3
  • Synology NAS is inaccessible, showing "No network access" or "Connection failed"

    Problem Diagnosis Synology NAS cannot be accessed, the common reasons are as follows: Network connection problems - NAS and computer are not on the same LAN, or network cable/switch failure IP address conflict/change - NAS IP has changed, DDNS is not effective Service not started - DSM service crashes or does not turn on Hard disk failure - Storage pool corruption......

    2026-4-2
  • Solution to the problem that the router login IP address cannot be found

    If you want to change the password or set WiFi on the home router, open the browser and enter 192.168.1.1, the result page cannot open? Don't panic, this is all too common. Today we will help you analyze the causes and provide solutions in order of success rate. Problem diagnosis: Why can't it be opened? Let's first clarify the fact that the router's login IP is not necessarily 192.168.1.1. Common: 192.168.1.1 (most, TP-Link, Xiaomi, etc.) 192.168.0.1 (ZTE、......

    2026-4-1
  • The router management page cannot be opened, and 192.168.1.1 or 192.168.0.1 cannot be entered

    Problem diagnosis The router management page cannot be opened (input 192.168.1.1 or 192.168.0.1 is unresponsive), the common reasons are as follows: Wrong connection method - You must connect to the router's LAN port with a network cable, or make sure that the WiFi is connected IP address is wrong - The default gateway of different brands of routers is different (Xiaomi is mostly 192.168.31.1, TP-Link is mostly 19......

    2026-4-1
  • List of necessary hardware configurations for building Black Synology

    Want to make a NAS but have a limited budget? Black Group is a good choice. But if you buy the wrong hardware, you will either not be able to run or get stuck as a dog. Today I will help you sort out the necessary hardware configuration of Hei Qun Hui, save money and not step on the pit. Problem diagnosis: Black Synology's hardware requirements Core principle: The hardware should match Synology's official requirements, but it can save money moderately. Synology official minimum requirements: CPU: x86 architecture (Intel or AMD) Memory: at least 2GB Storage: Any hard disk (number depends on the model) Black Synology advantages: Not subject to official hardware restrictions, can......

    2026-3-31
  • 192.168.1.1 Can't open, can't access the router login page

    Have you ever encountered this situation too: your newly purchased router is plugged in, and you excitedly open the browser and type 192.168.1.1, and the result shows that this website cannot be accessed? Don't panic, this is most likely not a broken router. Let's help you troubleshoot this problem today. Problem diagnosis The router management interface won't open, usually for the following reasons: Incorrect IP address - Your router may not be 192.168.1.1 Wrong connection method - Difference between Wi-Fi and wired connection Device conflict - ......

    2026-3-31
  • NAS only has a few tens of MB/s. Don’t blame the hard drive. Check these four things first.

    Gigabit LAN, theoretically the transmission speed can reach 125MB/s, but in reality, it only runs 60MB/s or even slower - the file is obviously in the NAS, and it takes half a day to copy a small movie. Most of the time, it's not a NAS performance issue, but rather a link in the network link that is holding it back. 1. Test the speed first and locate which section of the bottleneck Before troubleshooting, run it with the iPerf or NAS speed test tool to confirm the direction of the problem: Judgment criteria: ......

    2026-3-27
  • DHCP assigned the wrong IP segment in OpenWrt, three steps to troubleshoot and fix it

    After flashing OpenWrt, everything worked fine, but a device suddenly couldn't access the Internet, and when I looked at the IP address—not the regular 192.168.1.x, but the strange 10.x.x.x or 172.x.x.x address. This is usually caused by a DHCP server configuration problem, IP segment conflict, or LAN interface misconfiguration. 1. Confirm first: Which link is the problem in the OpenWrt console (LuCI)......

    2026-3-27

Contact Us

Online Consultation: Click here to send me a message

WeChat ID: master_135

Scan to follow