-
After three years of use, China Telecom optical modem's network has become increasingly laggy. It's not because the broadband is slowing down. After taking a look at the data, it turns out that 80% of the time it's because the cat is tired.
The broadband speed has not slowed down, and the mode light is all green. Why is the network at home getting slower every year? I compared two telecom optical modem that have been used for three or four years and explained the three real sources of performance degradation of optical modem.: Dial-up forwarding relies on the same CPU, the memory becomes more and more full, and the firmware becomes heavier and heavier. Attached is the troubleshooting sequence and a hard indicator to determine whether to change the modem. ...
-
Detailed explanation of BSS color of router WiFi6: The building is full of neighbors. The corridors are crowded into a pot of porridge. This invisible switch is secretly working.
What does the BSS coloring on the WiFi6 router parameter page mean? Neighbors all squeeze into the same channel. WiFi6 stamps the packets of each network with different colors, so packets can be sent simultaneously on the same frequency. This article uses actual measurements of fighting with 23 signals in the building to explain how BSS color works, how to adjust the spatial multiplexing threshold, why old equipment cannot enjoy it, and a division of labor table for channel selection and coloring. ...
-
How to accurately measure the speed of NAS solid-state drives: The night I dropped from 230MB/s to 80MB/s, I figured out whether I was measuring the cache or the disk.
On the SSD in the NAS, Windows copies a large file at 230MB/s, but BT download only leaves 80MB/s overnight. Is the drive broken or is the test wrong? This article explains how the cache layer deceives the speed test, what the three commands hdparm, dd, and fstrim measure respectively, how to configure the download disk buffering and TRIM, and attaches the actual measurement data of my N100 Feiniu for a year and a half. ...
-
If the panel's AP room WiFi suddenly runs out, don't disassemble it yet—it's probably stuck on the AC and that cable
The AC+AP network at home was working well, but one day the WiFi in one room suddenly disappeared, and everything in other rooms was normal. The panel AP in my study had this problem. From thinking the panel was dead to finding out it was the cable on the switch, I struggled all night. This article arranges the inspection order according to probability.: First, distinguish whether the WiFi is gone or the entire port is gone, and then see if the AC backend recognizes the panel. If it doesn't work, it's time to remove the panel. ...
-
192.168.1.1 Bounce a red warning saying the connection is not private, don't panic yet, three different appearances and three point methods
Open on mobile phone or computer 192.168.1.1 , a whole page of red text pops up suddenly: Your connection is not private and attackers may be able to steal your information. When I first encountered it, I thought the router was hacked. In fact, 90% of the time it was the browser forcing https. This article will talk about the three types of warnings separately, how to click each type, why you can safely enter the password in the http background at home, and three real faults that cause the warning to click but still cannot be entered. ...
-
While at the office, I remotely rescued a Xiaomi router that had been disconnected, navigating every pitfall the app couldn't kick off
I am at home at work and my WiFi is down. How can I remotely rescue a Xiaomi router? Here are the things I can save through actual testing:: Restart the Mijia App remotely, log in to 31.1 via the Neighbor Network, and then call again after powering off. This article will explain each of the pitfalls that cannot be eliminated by turning around the app, and the consequences of the device rushing to get the wrong house number after a call comes in. ...
-
There were too many router devices, and the camera vacuum was set to a dedicated WiFi, and the mainnet was smooth that night
What should I do if there are so many smart devices at home that they are disconnected and the main network card becomes a slide? I allocated more than 30 cameras, sweepers, and speakers in my home to a separate "device-specific WiFi", and the main network went smoothly that night. This article records the whole process of my actual testing according to the four paths.: New SSID grouping for 0 yuan, guest network method, VLAN walling method for 60 yuan, old router private network method, and other equipment that must not be moved. ...
-
Weak WiFi signal from the optical modem is due to the built-in antenna's low power. Four ways to fix it: one stop-loss line
Why is there only one bar of optical modem WiFi signal across the wall? You'll know once you take it apart and look at it: The built-in antenna, low transmit power, and being stuffed into a metal weak current box are the inherent shortcomings of the hardware layer. This article describes the whole process of helping my mother-in-law’s home WiFi rescue signal. Four tricks ranging from zero to dozens of dollars, and a stop-loss line for when to give up and stop fussing. ...
-
Mercury Tengda's LAN port speed is set like this: the gigabit card 94M is blocked by the 100M port
The Gigabit broadband speed test is stuck at 94M. Both broadband and optical modems have been checked and there is no problem. The real culprit is the LAN port of the Mercury or Tenda router. In this article, I write about how I recognized the 100M port in the background, which common models have 100M port, the overturn scene when the router was used as a switch, and how to calculate the account that cannot be changed and can only be replaced by a machine. ...
-
The China Telecom optical modem changed its WiFi name, and the ChinaNet thread couldn't tell who was who
How to change the name of Telecom optical modem WiFi? The string "ChinaNet" in the mobile phone's WiFi list starts with the default name of optical modem. I couldn't recognize whose name it was when I bumped into my neighbor's name. This article records the whole process of changing the name of the three telecom optical modem.: The useradmin permission is enough, the renaming entrances of the three models are compared, the pitfalls of dual-band needing to be changed twice, and which devices need to be reconnected after changing, and the work is done in ten minutes. ...

