-
Human presence sensors are very different from body sensors; swapping four is the only way to avoid turning on the lights
The lights in the bathroom went off when I was sitting still, and the lights in the study turned off after a few minutes of typing on the keyboard. I thought the sensor was broken at first. It took three dismantlings to figure out that the human body sensor only recognizes large movements, while the human presence sensor even counts breathing as "presence". This article explains the differences, actual measured results and four installation pits by room. ...
-
192.168.1.1 keeps redirecting back to the login box; just turn off this setting
Lose right 192.168.1.1 When I entered the management password, the login box flashed back to me when I logged in, and I was kicked out within two seconds of entering the background. I helped my neighbor wait in line all night. In the end, it was not the router that was broken or the password that was wrong, but the browser cookies and router time that were causing trouble. This article writes down the four steps of incognito window, system time, power off and restart, and changing browsers. Try them in order. Most of them do not require reset. ...
-
Xiaomi router: 192.168.31.1 binds a fixed IP in two steps
As soon as the printer and NAS at home are restarted, they cannot be found on the computer, and port forwarding also fails. I checked and found out that the IP sent by DHCP changes every time. Enter Xiaomi router 192.168.31.1 , bind the device MAC and fixed IP together, and printers and NAS will no longer change addresses randomly. This article describes how to hide the address pool, how to copy the MAC, and how to recheck after binding. ...
-
500M broadband only runs 94M, WAN port switched to 1000M full duplex
After setting up a 500M broadband connection, the router background shows that the WAN port only reaches 100M, and the speed test keeps stuck at 94M. I checked the network cable, crystal head, and optical modem port, and finally changed the WAN port speed from auto-negotiation to 1000M full-duplex in the background of the router, and the network speed returned to 480M. This article records the path setting and the two pitfalls that have been encountered. ...
-
Change the WiFi name of the Mercury Tengda router, and change the two bands twice
My Mercury D191G and my relative's Tenda AC10 have both changed their WiFi names. On the first trip, only 5G was changed and 2.4G was missed. The sweeper and old mobile phone couldn't connect at all. This article outlines the specific entrances to Mercury Tengda's two backends, the three rules before changing the name, and the troubleshooting procedures for reconnecting after the complete change. ...
-
Before switching to the modem, make sure to note the parameters and make sure not to miss VLANs or voice beyond LOID
I just copied the LOID and changed to Shin Kong Cat, and the registration card was at 40%. This article explains by Telecom, China Unicom and China Mobile which parameters should be copied from the old mode backend and stickers before replacing the modem. VLAN, voice and SN are the three most easily leaked. If anything is missed, you may not be able to access the Internet. ...
-
If you change the telecom optical modem to WiFi encryption, select the wrong dropdown box and disconnect FamilyMart
The wireless security or encryption mode drop-down box in the backend of Telecom Optical Mode often defaults to WPA/WPA2 mixed. The inability of older devices to connect is probably related to it. This article explains how to change the frequency bands of 2.4G and 5G respectively, how to choose between WPA2 and hybrid mode, and how to reconnect all the devices after changing them. ...
-
Understanding the ping's TTL, the 64 and 128 immediately recognized the opposing device
What do the lines ttl=64 and ttl=128 after ping mean? It is not a delay, it is the remaining number of times that the packet decreases by 1 each time it passes through a router. I pinged my home router, Windows computer, and NAS one by one, and checked the three settings: 64, 128, and 255. I will talk about the two pitfalls that are most likely to be misjudged. ...
-
Steps to map network drives on NAS: Win11 and Mac mount Z drive in two steps, no more red cross after restart
How to mount a NAS shared folder as a Z drive on the computer in Windows? I wrote down the pitfalls I encountered on Win11 and Mac.: How to fill in the address, why the account is always rejected, and how to fix the drive letter that turns into a red cross after restarting. It is compatible with Synology and Feiniu. Just click on it and you can use it like a local hard drive. ...
-
192.168.1.1 If you enter the wrong password several times, you will be locked.: It says there are too many attempts. Please wait a few minutes and try again.
exist 192.168.1.1 After entering the wrong management password several times in the background, the page suddenly pops up "Too many attempts." Many people's first reaction is that they have been hacked and are in a hurry to reset. This article records my experience of locking myself out: How to distinguish between a temporary lock and a real password change? How long does it take for each device to be locked? There are also four self-rescue procedures: wait, change window, restart, and reset. Don’t panic and restore to factory settings. ...

